SMARTECH
VIEW MORE
SMARTECH
VIEW MORE
SMARTECH
VIEW MORE
PRODUCTS
• Consists of 2 or 4 equal size hermetic scroll compressors.
• Compact size brazed plate heat exchanger (BPHE) cooler for chiller smaller than 31.0 R.tons.
• Shell and tubes direct expansion cooler with dual refrigerant circuits for chillers larger than 40.0 R.tons.
• One or multiple axial propeller fans with low noise level.
• Factory packaged and prewired power and control panel.
• Smart-Advance SA33 microprocessor based controller for infinite capacity steps modulation and safety protection.
PRODUCTS
• Constructed from galvanized steel sheet casing cabinetry.
• Two or multiple variable speed drive scroll compressors.
• Shell and tube DX evaporators.
• Copper tubes- Aluminium hydrophilic fins condenser coil for efficient heat transfer.
• Two or multiple axial propeller fans with direct drive induction motors.
• Factory packaged and prewired power and control panel.
• Microprocessor-based controller for infinite capacity steps modulation and safety protection.
• Suitable for outdoor installations with free and unducted condenser fans air discharge.
PRODUCTS
• Twin rotary screw compressors.
• Available with HFC407c refrigerant.
• Shell and tube direct expansion evaporator.
• Aluminium hydrophilic fins condenser coil for efficient heat transfer.
• Multiple axial propeller fans with direct drive inductions 3-phase motors or optional EC motor condenser fan to reduce overall unit power input.
• Factory packaged and prewired power and control panel.
• Included microprocessor-based controller for capacity steps modulation and safety protection.
• Suitable for outdoor installation with free and unducted condenser fans air discharge.
PRODUCTS
• Twin rotary screw VSD compressors.
• Available with HFC134a refrigerant.
• Aluminium hydrophilic fins condenser coil for efficient heat transfer.
• Multiple axial propeller fans with direct drive inductions 3-phase motors or optional EC motor condenser fan to reduce overall unit power input.
• Factory packaged and prewired power and control panel.
• Included microprocessor-based controller for capacity steps modulation and safety protection.
• Suitable for outdoor installation with free and unducted condenser fans air discharge.
PRODUCTS
• R410A air-cooled split air-conditioners with a capacity size from 6 R.tons to 112 R.tons.
• The unit can be completely factory wired and packaged with starters and safety control, pre-charge with full refrigerant charge; and ready for installations.
• The evaporator-blower unit consists of 1-inch-thick polyurethane insulated double-wall casing cabinetry, AMCA certified centrifugal forward curved fan, high efficiency TEFC motor and dynamically balanced and aligned drive package.
• The blower fan can be optionally ordered with top or horizontal supply air discharge connection.
• Each evaporator unit also comes with hydrophilic coated evaporator coil with thermal expansion valves.
• The condenser unit comes with low noise and highly efficient axial propeller fans.
• Each condensing unit also comes with hydrophilic coated condenser coils for improved heat transfer and incorporate with single and multiple hermetic scroll compressors with independent refrigerant circuits.
• Heavy gauge galvanized steel casing, coated with epoxy polyester paint, to enhance weatherability and corrosion resistance.
PRODUCTS
• Double wall polyurethane foam insulated casing panel with thermal break construction.
• Air flowrates from 2,400CFM to 50,000CFM. Units higher than 50,000CFM can be custom engineered and manufactured.
• Direct drive Ziehl-Abegg Centrifugal Plug fan.
• High efficiency EFF1 motors, with variable frequency speed drive operation.
• Cooling coils with pre-coated hydrophilic aluminium fins.
• Coil filter section designed with adequate space.
• Wide choice of accessory sections including fillers, diffuser, mixing box, humidifier, heat pipe, energy wheel heat recovery, silencer and etc.
• Smartwise Intelligent microprocessor control panel which can be interfaced with Building Management System.
PRODUCTS
• Double wall polyurethane foam insulated casing panel with thermal break construction.
• Air flowrates from 2,400CFM to 50,000CFM. Units higher than 50,000CFM can be custom engineered and manufactured.
• Cooling coils with pre-coated hydrophilic aluminium fins.
• Different types and construction classes of fans such as forward curve fan, backward fan, air foil fan and plug fan can be selected with high efficiency EFF1 motors drive package to meet a particular application requirement and to provide flexibility.
• Single zone AHU or multi zone AHU, provides flexibility to suit any installation and application requirement.
• Wide choice of accessory sections including fillers, diffuser, mixing box, humidifier, heat pipe, energy wheel heat recovery, silencer and etc.
PRODUCTS
• Capacity range: 300CFM to 500CFM (Compact) or 600CFM to 1500CFM (Standard).
• Compact design, simple installation and easy maintenance.
• Unique 3D design of the centrifugal fan ensures extra quiet operation & high efficiency.
• 4-way air supply panel is standard, 360⁰ air supply panel available as an option.
• Built-in drain water pump with 500mm (Compact) & 750mm (Standard) pumping head.
• LED display with error code for easy fault diagnostic.
• Wireless remote with LED display, wired control is optional.
• Air outlets at sides of unit are available. These can be connected by duct to supply air to nearby small rooms.
PRODUCTS
• Flexible for installation; designed for horizontal/vertical and concealed /cabinet application.
• Ultra thin body, streamlined appearance.
• 220-240V /1ph / 50hz power supply is standard.
• Movable louver for wide angle air flow.
• Air return from the side or below for increased flexibility.
• 3-way electromagnetic valve can be built inside.
• Remote controller is optional.
PRODUCTS
• Capacity range: 200~2000CFM.
• Wide external static pressure supplying. Three external static pressure (12Pa/30Pa/50Pa) settings for added flexibility.
• Standard extended drainage pan for protecting your ceiling better.
• Left or right hand piping connections, field convertible.
• Flexible control, remote controller and wired controller are optional.
• A patent design is able to prevent abnormal noise caused by blowing fins.
• Higher efficient heat exchange for complete contranatant flow.
• Return air plenum and filter are standard.
• Fresh air supply makes life healthier and more comfortable.
• 220-240V/1Ph/50Hz power supply is standard.
PRODUCTS
• High air volume, high static pressure and high capacity.
• High-pressure centrifugal fans.
• Easy to clean and change the air filter.
• Standard extended drainage pan for protecting your ceiling better.
• Return air plenum and filter are standard.
• Four-speed motor with one reserved for more choice.
• Pipe connection from left or right can be selected (in factory).
• 220--240V/1Ph/50Hz power supply is standard.
• Flexible control, remote controller and wired controller are optional.
PRODUCTS
• LED display display.
• Crossflow fan creates quiet and comfortable environment.
• Multi piping connection; left/ right/ rear, to suit any installation requirement.
• Easy maintenance with removable front panel.
• 220-240V/1Ph/50Hz power supply is standard.
• Built-in 3 way electromagnetic valve.
• Wireless remote control with LED display is standard,wired control is optional.
PRODUCTS
• Ducted DBA fan coil units (FCU) come with various capacity sizes from 28MBH to 280MBH.
• The air flow rate ranges from 800CFM to 8400CFM.
• Each FCU comes with Totally Enclosed Fan-Cooled (TEFC) motors and belt-driven forward curve centrifugal blowers. The FCUs shall be suitable for application where external static pressure may vary from 0.5” w.g. to a maximum of 2.5” w.g. without excessive noise.
• These FCUs are readily adapted to a wide variety of ceiling mounted installation where low noise break-out and ease of access to internal components for preventive maintenance are important criteria for consideration.
• Typical unit can accommodate a cooling coil from 3 rows deep to 6 rows deep, either of chilled water or DX type (using refrigerant R410A).
• An unlimited selection of factory installed control systems is available for DBA models.
PRODUCTS
• R410A ducted ceiling mounted water-cooled packaged unit with a capacity range from 13MBH to 485MBH.
• The unit consists of 1-inch-thick polyurethane insulated double-wall casing cabinetry.
• The evaporator section uses AMCA certified forward curved fan which is direct driven or belt-driven by TEFC motor fan and the evaporator coil is hydrophilic coated.
• The unit comes with sealed-hermetic rotary or scroll type compressor.
• The condenser is brush cleanable shell-and-tube type.
• Units are factory assembled, system pressure and leak tested, evacuated, dehydrated and pre-charged with refrigerant.
PRODUCTS
• Ducted DDA fan coil units (FCU) come with various capacity sizes from 19MBH to 120MBH.
• The air flow rate ranges from 600CFM-3500CFM.
• Each FCU comes with Permanent Split Capacitor (PSC) motors and direct drive forward curve centrifugal blowers. The FCUs shall be suitable for application where external static pressure may vary from 0.2” wg to a maximum of 0.7” wg without excessive noise.
• These FCUs are readily adapted to a wide variety of ceiling mounted installation where low noise break-out and ease of access to internal components for preventive maintenance are important criteria for consideration.
• Typical unit can accommodate a cooling coil from 3 rows deep to 6 rows deep, either of chilled water or DX type (using refrigerant R410A).
• An unlimited selection of factory installed control systems is available for DDA models.
PRODUCTS
• Slim all metal housing with esthetic curved design.
• Full metal shell, and minimal maintenance.
• Easy installation and cleaning.
PRODUCTS
SSCD180AR7-XQP Air-cooled Screw Chiller
- Hazardous Application: Class I, Div 2, Group B&C.
- Fitted with 2 ATEX Certified Compressors.
- NEMA 4X SS304 Electrical Box Connected to a Purge Unit and Pressurize with Inert Gas.
- Explosion proof motor, Spark proof fan, Ex-proof Solenoid Valve, Electrical rigid conduit.
PRODUCTS
• R410A ducted ceiling mounted water-cooled packaged unit with a capacity range from 95MBH to 1478MBH.
• The unit consists of 1-inch-thick polyurethane insulated double-wall casing cabinetry.
• The evaporator section uses a AMCA certified forward curved fan which is belt-driven by TEFC motor fan and the evaporator coil is hydrophilic coated.
• The unit comes with sealed-hermetic scroll type compressor.
• The condenser is brush cleanable shell-and-tube type.
• Units are factory assembled, system pressure and leak tested, evacuated, dehydrated and pre-charged with refrigerant.
PRODUCTS
• R410A air-cooled scroll compressors package with a capacity size from 6 R.tons to 131 R.tons.
• The unit can be completely factory wired and packaged with starters and safety control, pre-charge with full refrigerant charge; and ready for installations.
• The evaporator-blower section consists of 1-inch-thick polyurethane insulated double-wall casing cabinetry, AMCA certified centrifugal forward curved fan, high efficiency TEFC motor and dynamically balanced and aligned drive package.
• Each evaporator section consists of hydrophilic coated evaporator coil with thermal expansion valves for efficient superheat control.
• The blower fan can be, optionally ordered with top or horizontal supply air discharge connection.
• Heavy gauge galvanized steel casing, coated with epoxy polyester paint, to enhance weatherability and corrosion resistance.
• Low noise and highly efficient axial propeller fans.
• High efficiency condensing unit, suitable for ambient up to 125°F.
• Each condensing section consists of a large hydrophilic coated condenser coils for improved heat transfer and incorporate with single and multiple hermetic scroll compressors with independent refrigerant circuits.
PRODUCTS
• Ducted ECPF fan coil units (FCU) come with various capacity sizes from 21MBH to 280MBH.
• The air flow rate ranges from 600CFM to 8400CFM.
• Each FCU comes with high efficiency EC motors and direct coupled to centrifugal plug fans.
• The FCUs shall be suitable for application with external static pressure of up to 2.0” w.g. without excessive noise.
• These FCUs are readily adapted to a wide variety of ceiling mounted installation where low noise break-out and ease of access to internal components for preventive maintenance are important criteria for consideration.
• Typical unit can accommodate a cooling coil from 3 rows deep to 6 rows deep, either of chilled water or DX type (using refrigerant R410A).
• Each FCU shall be provided with a factory mounted speed controller to allow manual adjustment for fan-motor speed to meet specified side airflow rates versus external static pressure requirements.
PRODUCTS
SSCD120AR7-Q Process Cooling Chiller
- R134a, 66 tons, 30% Propylene Glycol, Water IN/OUT 37.8/31.0 F, 98 F Ambient.
- For EDC Storage Tank Facility.
- Copper Tube Copper Fin Condenser Coil.
- Nema 4X SS304 Electrical Box with External Cable in Rigid Conduit.
- Rigid Base Frame Constructed with 10”x3/8” C-Channel and Hot Dipped Galvanize.
- Welded Condenser Support.
PRODUCTS
Ziehl Abegg Direct Drive Plug Fan with VFD control
- 2” 4lb/ft3, Fiberglass Panel with Perforated Internal Liner at Fan Compartment.
- Required Low Sound Level at various Octave Band Frequency, Room NC 25.
- Unit Tested to ISO 5136 Acoustic Standard before delivery.
PRODUCTS
Low Temp Air-Cooled Chiller SSCD200AR4Q-LT, R404a
- 75.3 TR, Dynalene HC30, Water IN/OUT +8/0°F, 89°F Ambient.
- 2nd stage External oil separator to improve discharge side oil separation.
- Oil cooler with Filter, Oil Flow Switch and Regulator Valve.
- Suitable for Low Ambient Operation down to 0°F.
PRODUCTS
• R410A air-cooled scroll compressors package with a capacity size from 6 R.tons to 112 R.tons.
• The unit can be completely factory wired and packaged with starters and safety control, pre-charge with full refrigerant charge; and ready for installations.
• The evaporator-blower section consists of 1-inch-thick polyurethane insulated double-wall casing cabinetry, AMCA certified centrifugal forward curved fan, high efficiency TEFC motor and dynamically balanced and aligned drive package.
• Each evaporator section consists of hydrophilic coated evaporator coil with thermal expansion valves.
• The blower fan can be, optionally ordered with top or horizontal supply air discharge connection
• Heavy gauge galvanized steel casing, coated with epoxy polyester paint, to enhance weatherability and corrosion resistance.
• Low noise and highly efficient axial propeller fans.
• Each condensing section consists of a large hydrophilic coated condenser coils for improved heat transfer and incorporate with single and multiple hermetic scroll compressors with independent refrigerant circuits.